Your SEO optimized title

Sonifex RB-ADDA A/D and D/A Converter

Sonifex RB-ADDA A/D and D/A Converter

Sonifex RB-ADDA A/D and D/A Converter

SKU: 16790

Cat no: 6013

  • Rack mounted
Add to wishlist

Estimated Delivery 1 to 2 days

£465.00 (ex vat) £558.00 (incl vat)

Sonifex RB-ADDA A/D and D/A Converter



The RB-ADDA A/D and D/A converter is a 1U rack-mount which produces an AES/EBU or S/PDIF level digital audio output from a balanced XLR or unbalanced phono stereo audio input. It also produces a stereo balanced XLR or unbalanced phono output from an incoming AES/EBU or S/PDIF digital input signal.
The unit operates in four modes:
Master Mode - In this mode the unit receives an analogue audio signal, which is digitised and formatted for digital serial transmission (IEC958). The necessary clock signals are generated internally from an on board master clock at a selectable rate (32kHz, 44.1kHz, 48kHz, 88.2kHz or 96kHz).
Slave Mode - In this mode the unit automatically detects the presence of a digital audio sync signal, if present at the digital input, and synchronises the digital output to it. If no sync is present, no output will be generated.
Auto Mode - Here the unit synchronises to the digital audio sync signal if present at the digital input and uses the internal master clock only if no sync input signal is detected. In this case, the internal master clock is used at the selected sample rate.
Auto Lock Mode - This operates like the auto mode except that if no sync input signal is detected, it will use the internal master clock to sync to the sample rate which was last clocked to.
When operating in sync modes, the front panel power LED flashes whenever the unit is not synchronised to the incoming digital signal.
The analogue inputs have left and right level controls using pre-set potentiometers and DIP switches allowing a signal range from +9dBu to +27dBu. The RCA phono inputs have a further 10dBu gain incorporated to give a total gain range of -1dBu to +17dBu for full-scale digits. The analogue outputs have an output level control, allowing full-scale settings selectable from +12dBu, +18dBu or +24dBu. There are factory-set internal level controls for the analogue outputs allowing gain adjustment of ±1dB.
There are buttons to select either the AES/EBU or S/PDIF input or output for the D/A and A/D sections respectively.
The output bit depth can be selected from 16, 20 or 24 bits. Inputs of a different bit depth to the output are dithered using a psychoacoustic noise filter.
For the digital output, there is a switch available to define the content of the channel status bits embedded within the digital audio stream. The channel status bits will be forced to Professional Mode for sample rates above 48kHz as they are not supported by the Consumer Mode. For sample rates of 32kHz, 44.1kHz and 48kHz, the status bits can be forced to either Professional or Consumer Mode.

Product Specification

Maximum Input Level +27dBu balanced inputs, +17dBu unbalanced inputs
Input Impedance >10kohms unbalanced, >20kohms bridging unbalanced
Dynamic Range >110dB
Gain Range Adjustable input gain of +/-3dB on 12dBu, 18dBu or 24dBu, ref FSD
Distortion and Noise >96dB THD + N at 1kHz
A/D Connections
Analogue Inputs 2 x XLR 3 pin (balanced)
2 x RCA phono (unbalanced)
Digital Outputs 1 x AES/EBU XLR 3 pin male
1 x S/PDIF RCA phono
Mains Input Filtered IEC, switchable 110-120V, or 220-240V, fused, 10W max

Analogue to Digital Conversion
D/A Audio Specification
Maximum Output Level +24dBu balanced inputs, +14dBu unbalanced inputs
Output Impedance 100dB
Gain Range Selectable 12dBu, 18dBu or 24dBu output level, ref FSD
D/A Connections
Digital Inputs 1 x AES/EBU XLR 3 pin female
1 x S/PDIF RCA phono
Analogue Outputs 2 x XLR 3 pin male (balanced)
2 x RCA phono (unbalanced)

Operational Controls
Analogue Input Select XLR or phono, via push-switch
Digital Output Select AES/EBU or S/PDIF, via push-switch
Digital Input Select AES/EBU or S/PDIF, via push-switch
De-emphasis On/Off DIP switch
Input Level Adjust DIP switch and preset pots
Bit Depth 16, 20 or 24 bits via DIP switch
Modes & Frequencies 16 way rotary DIP switch
Channel Status Bits Forced to consumer mode or professional mode, via DIP switch
Output Level Adjust DIP switch
Physical Specification
Weight Nett: 1.6kg
Gross: 2.2kg
Dimensions Raw: 48cm (W) x 10.8cm (D) x 4.2cm (H) (1U)
Boxed: 53cm (W) x 20.5cm (D) x 6cm (H)

Questions & Answers

There are no questions for this product yet.

Ask a Question...

Please login to your account to post a question.